İTS Gıda & Lojistik
EN
Get a Quote
Home · Articles · Storage
Storage

Precooling and Shelf Life in Fruit and Vegetables: Removing Field Heat

Why is rapidly removing field heat after harvest critical? Room, forced-air, hydro and vacuum precooling methods, respiration rate, ethylene sensitivity, humidity, circulation and storage intake control.

30 August 2026 · 14 min read
Precooling and Shelf Life in Fruit and Vegetables: Removing Field Heat

Fruit and vegetables do not die once harvested; they continue to respire, lose water and ripen. The only real way to slow this vitality is to rapidly lower the produce's temperature. A crate of peppers picked on a summer morning in the Aegean leaves the field with a core temperature above 30°C; every hour that passes before that heat is removed is a permanent loss from shelf life. Pre-cooling is exactly this task: removing the field heat before the produce enters storage. Below, we explain the methods, the selection rules by produce group, and store intake control from the field.

Why field heat is the most expensive load

A cold store is sized to keep produce cold, not to cool it down. This sentence sounds like a cliché, but in practice most of the problems experienced stem from ignoring it. When pallets arriving at field temperature are put straight into the store, three things happen at once: the room temperature rises and damages the other produce inside, the evaporator is forced to work beyond its capacity, and the newly arrived produce itself can take days to reach the target temperature.

This last point is the most commonly overlooked. A pallet may carry a high temperature at its core for days even though its outer layers look cold. The store thermometer shows the target reading, not the inside of the produce. When produce sent out for shipment arrives at the customer wilted, the vehicle or the store is usually blamed; in fact, the loss occurred in the first hours after harvest.

The cost of time is something that can be measured. Produce left waiting in the sun in the field can rise above ambient temperature; this difference is pronounced in dark-coloured produce with a large surface area. Harvesting in the cool hours after sunrise, keeping crates in the shade, and setting up a simple canopy over the collection area all lower the produce's starting temperature without spending any energy. Pre-cooling comes into play only after these low-cost measures.

The economics of pre-cooling are equally clear-cut. The energy spent per unit of produce is almost always lower than the cost of the shelf life lost and the return rate incurred. For a business selling to chain retail, the matter is even simpler: produce that fails to meet the required remaining shelf life does not fetch a good price. Here, pre-cooling is not a cost item but an investment that keeps the produce sellable.

Respiration rate, heat production and ethylene sensitivity

The two core concepts of postharvest physiology are respiration and ethylene production. Respiration is the process by which produce generates energy by consuming its own stored reserves, releasing carbon dioxide, water vapour and heat in the process. The higher the respiration rate, the faster the produce ages. Temperature directly governs the respiration rate: for every 10 °C rise in temperature, the respiration rate roughly doubles or triples. This single sentence contains the entire rationale for pre-cooling.

Produce can be grouped into three categories according to respiration rate. Low-respiration produce includes items that store well for long periods, such as onions, garlic, potatoes, apples and citrus. Moderate-respiration produce includes items such as peaches, apricots, tomatoes, peppers, carrots and cabbage. High-respiration produce comprises short-lived items such as broccoli, green beans, spinach, mushrooms, lettuce, spring onions and strawberries. The high-respiration group benefits most from pre-cooling and forgives delay the least.

Ethylene is a plant hormone that accelerates ripening; being colourless and odourless, it goes unnoticed in storage. Apples, pears, bananas, melons, apricots, peaches, plums, avocados and tomatoes are high ethylene producers. Lettuce, spinach and other leafy greens, broccoli, cauliflower, cucumber, courgette, carrots and cut flowers, on the other hand, are highly sensitive to ethylene; yellowing, softening, bitterness and premature decay in these products are typical signs of ethylene exposure.

Temperature is decisive here too: both ethylene production and the response to ethylene slow down as temperature falls. In other words, pre-cooling suppresses not only respiration but also ethylene-driven ageing. Cooling alone, however, is not enough; producing and sensitive products must also be kept separate, along with proper ventilation and, where necessary, the use of ethylene scrubbers.

A warning also comes from the opposite direction: not every product likes the cold. Bananas, tomatoes, cucumbers, aubergines, courgettes, peppers, avocados and pineapples suffer chilling injury at low temperatures. Symptoms include surface pitting, internal browning, failure to ripen and loss of flavour; these often only appear once the product leaves storage and returns to room temperature. For these products, the goal of pre-cooling is not a temperature close to zero but their own safe range. Potatoes are a separate case: at very low temperatures, starch converts to sugar and frying quality deteriorates.

Pre-cooling methods and which products they suit

Room cooling: The product is placed in a cold room and left to cool via the room's own air circulation. It is the simplest and most common method, requiring no extra equipment. It is, however, the slowest; the cold air reaching the produce inside a pallet is limited, and the core temperature can take days to drop. Using vented crates, stacking pallets loosely and leaving gaps between pallets significantly shortens the process. It is an acceptable method for long-shelf-life, low-respiration products.

Forced-air cooling: Pallets are arranged in two facing rows, one end of the aisle between them is sealed with a tarpaulin, and a fan at the other end draws air through, forcing cold air through the vents in the crates. This way, the air passes through the product rather than around it. It delivers far faster results than room cooling and is the most widely used solution for the majority of fruit and vegetables. The requirement is that the crates have sufficient ventilation holes and that these are not covered with stretch film; a fully wrapped pallet renders a forced-air system ineffective.

Hydro-cooling: The product is immersed in cold water or has cold water sprayed over it. Because water is a far more effective heat carrier than air, cooling is fast and the product loses no moisture — indeed, it may even absorb some. It works very well for firm-skinned, water-tolerant produce: carrots, celery, leeks, radishes, cherries, peaches, melons, watermelons, sweetcorn and broccoli are typical examples. It is not suitable, however, for soft fruits such as strawberries, grapes and figs, or for dry-skinned produce such as onions and garlic. The critical point in hydro-cooling is water hygiene: since the same water passes through many batches, disinfection, filtration and a water-change schedule are essential; otherwise the system becomes a cross-contamination route.

Vacuum cooling: The product is placed in a sealed chamber and the pressure is reduced; at lower pressure, water evaporates at a lower temperature, and this evaporation draws heat out of the product. It is extremely fast for products whose surface area is large relative to their volume; leafy greens such as lettuce, spinach, rocket and parsley are cooled within minutes. The trade-off is water loss: roughly one per cent of the product's weight evaporates as water for every 5-6°C drop in temperature. This is why, in most systems, the product is moistened before or during the process. Vacuum cooling is not efficient for spherical, dense products with low surface area, such as tomatoes, potatoes and apples.

Icing: Crushed ice is placed inside or on top of the crate. It is traditionally used for products such as sweetcorn, broccoli and spring onions; its advantage is that it continues cooling the product throughout transport. It requires water-resistant packaging and increases transport weight.

Method selection is based on three questions: is the product water-resistant, is its surface area large relative to its volume, and does its packaging allow air through? Choose vacuum cooling for leafy, water-sensitive products; hydro-cooling for water-resistant, firmer products; forced-air cooling for perforated packaging and general-purpose use; and room cooling for long shelf-life, tolerant products. Having more than one method in the same facility is common in plants handling a wide range of products.

Measuring the cooling rate: the one-seventh rule

How long precooling takes is established by measurement, not estimation. The metrics used in the industry are the half-cooling time and the one-seventh cooling time. The half-cooling time is the time it takes for the temperature difference between the product and the cooling medium to fall by half. The one-seventh cooling time is the time it takes for this difference to fall to one-seventh, and in practice this is the point at which precooling is considered complete.

Let's look at an example. If the product is at 30°C and the cooling medium is at 2°C, the difference is 28 degrees. The one-seventh point is where the difference falls to 4 degrees, meaning the product reaches approximately 6°C. Closing the remaining difference becomes progressively slower, which is why trying to bring the product to the exact target temperature during precooling is inefficient. The last few degrees are closed once the product is in storage.

Measurement is taken from the core of the product, not from the air temperature. An insertion probe thermometer is used on units taken from different points of the pallet, with particular attention to the centre of the pallet and the corner furthest from the airflow. Measuring a single unit is misleading; readings are taken from at least three to five points, and the highest value is taken as the reference. The accuracy of the probe thermometer can be simply confirmed with a zero check in an ice-water mixture.

The real benefit for the business is that these measurements only need to be taken and recorded once. Once the one-seventh cooling time has been established for each product and each packaging type, a reliable duration can be applied to subsequent batches without further measurement. This table is one of the most useful internal documents a business can have: it answers questions such as how many hours forced-air cooling should run for a given product, what fan speed to use, and how many minutes a particular package takes to cool.

The effect of packaging on cooling speed also becomes visible in this measurement. When the same product is measured in a perforated crate versus a sealed box, the difference in time is striking. The ratio of crate perforations to total surface area, the alignment of the holes (the perforations of stacked crates should overlap), and ensuring internal dividers don't block the airflow path are all design decisions that directly affect cooling time.

Relative humidity, moisture loss and air circulation

In fruit and vegetables, almost all weight loss is moisture loss, and this loss shows up not only on the scale but also in appearance: wilting, wrinkling, loss of shine and stem drying. A moisture loss of just a few per cent is enough to push many products past the limit of saleability.

What determines moisture loss is the humidity difference between the product surface and the surrounding air. This is why relative humidity in fruit and vegetable stores is generally kept in the 85-95% range. High-surface-area products such as leafy greens, broccoli, carrots and fresh beans need the upper end of this range. Dry-skinned products, by contrast, need the opposite: onions, garlic and squash are stored at lower humidity, around 65-75%; at high humidity these products sprout roots and go mouldy. Placed in the same room, one dries out while the other rots.

The way to raise humidity is not always a humidifier. The greater the temperature difference between the evaporator surface and the room air, the more moisture the air sheds, drying out the room. Using a larger-surface evaporator, i.e. operating with a smaller temperature difference, is the most effective way of preserving the room's natural humidity. In addition, fine-pored liners placed inside perforated packaging reduce moisture loss by creating a high-humidity microclimate around the product; they are beneficial as long as they don't fully block airflow.

Air circulation should not be confused with air exchange. Circulation is the movement of air within the room around the product, ensuring temperature and humidity are uniform at every point. Air exchange, on the other hand, is the intake of fresh air from outside, needed to dilute the build-up of carbon dioxide and ethylene. Circulation should be continuous, while air exchange should be measured; in the summer months, excessive fresh air both increases energy costs and lowers the room's humidity.

The most common factor disrupting circulation is stacking. Pallets placed in front of the evaporator, stacks leaning against the wall, product piled up to the ceiling, and fully stretch-wrapped pallets all block the passage of cold air. We covered stacking rules and the in-store hot-spot map in detail in our article how does a cold storage facility work.

Products that should not be stored together

Whether products can share the same room depends on three criteria at once: temperature compatibility, humidity compatibility and ethylene-odour compatibility. If even one of the three fails to hold, the products are kept apart. In practice, the most commonly overlooked criterion is the third, because its effect is not seen immediately but over several days, and is often attributed to the wrong cause.

The classic incompatible pairs are as follows:

  • Apples, pears and melons with leafy greens, broccoli, carrots: Ethylene producers cause yellowing, bitterness and softening in sensitive products.
  • Bananas, tomatoes and avocados with cucumbers, courgettes: There is both an ethylene issue and a mismatch in these products' temperature requirements.
  • Onions and garlic with apples, pears and dairy products: Odour transfer is pronounced; in addition, onions and garlic require low humidity while the fruits require high humidity.
  • Potatoes with apples: Ethylene speeds up sprouting and flavour deterioration in potatoes.
  • Fish and seafood with dairy products and eggs: Products with a fatty composition absorb odours quickly.
  • Citrus fruits with odour-sensitive products: Volatile compounds released from the peel cause flavour transfer.

In single-room facilities this separation is hard to achieve, so the solution lies in the acceptance policy. The product acceptance form should flag each item as an ethylene producer, ethylene-sensitive or an odour source; incompatible items are not placed in the same room within the same week, or are not accepted at all. Where physical separation is not possible, it is done over time instead: one group is dispatched in the morning, the other in the afternoon, with the room ventilated in between.

Ethylene removal options are also available. Cartridges containing potassium permanganate, catalytic ethylene scrubbers and controlled-atmosphere systems reduce ethylene concentration. These do not replace separation but complement it; keeping incompatible products in the same room and relying on a scrubber rarely gives sufficient results at most operational scales.

Warehouse intake control and daily routine

The result of pre-cooling shows up at warehouse intake control. The check at the door consists of three measurements: product core temperature, visual quality and packaging integrity. Core temperature is measured with an insertion probe at a minimum of three points on the pallet and recorded. Products outside the acceptance range are either directed to pre-cooling or rejected; unconditional acceptance is the starting point of every loss that follows.

What to check visually is clear: bruises and wound marks, early signs of decay, mould, over-ripeness, foreign matter, and the condition of leaves and stems. A single rotten item in a crate spreads quickly to its neighbours in an enclosed environment; sorting at the door is far cheaper than sorting inside the warehouse. Packaging control, in turn, checks that ventilation holes are open and that crates are undamaged and stack properly.

Shelf assignment for accepted goods is made according to product group. Incompatible products are not directed to the same room; sensitive products are not placed near the door, in front of the evaporator, or in the warm corner of the room. The pallet label clearly shows the intake date, batch number and, where applicable, the best-before date in large print; rotation is managed through this label.

The daily routine can be summarised under four headings. Morning: reviewing overnight temperature records, checking the alarm list, and confirming that the pre-cooling unit and fans are running. During the day: temperature measurement and recording at every intake, tracking pre-cooling batch durations, and checking room humidity levels. Evening: visual confirmation that doors are closed, evaporator fronts are clear, and areas with water lines are clean. Weekly: probe thermometer checks, crate ventilation-hole condition, and recording hydro-cooling water changes.

The chain continues after the product leaves the warehouse; loading chilled product onto a vehicle that has warmed up gives back everything gained during pre-cooling within a few hours. We cover vehicle selection, loading temperature and record-keeping requirements for the transport leg in our refrigerated transport guide; the overall logic of the chain is covered in our why the cold chain matters article.

At İTS Gıda & Lojistik, we are planning fruit and vegetable processing, pre-cooling and cold storage processes at our facility under construction in Milas according to this control logic. Producers and supply chain managers in the region can get in touch with us to discuss storage and distribution solutions.

Frequently Asked Questions

What is the difference between pre-cooling and cold storage?
Pre-cooling is a one-off process carried out after harvest to rapidly remove the produce's field heat. Cold storage, on the other hand, is about keeping the produce at the temperature it has already reached. The store is sized to hold cold, not to create it; produce placed in storage without pre-cooling can take days to reach the target temperature and will also warm up the other produce in the room.
Which pre-cooling method suits which produce?
Vacuum cooling is preferred for water-sensitive, leafy produce (lettuce, spinach, rocket); hydro-cooling for water-tolerant, firm produce (carrots, celery, sweetcorn, peaches, melons); and forced-air cooling for general fruit and vegetables in perforated packaging. For long-shelf-life, low-respiration produce, room cooling may be sufficient.
How can you tell when pre-cooling is complete?
The seven-eighths cooling time rule is used: pre-cooling is considered complete once the temperature difference between the produce and the cooling medium has fallen to one-eighth of its initial value. Measurement is taken not from air temperature but from the product's core using a penetration probe, at a minimum of three different points on the pallet; the highest reading is taken as the reference.
Can all fruit and vegetables be kept in cold storage?
No. Produce such as bananas, tomatoes, cucumbers, aubergines, courgettes, peppers, avocados and pineapples suffers chilling injury at low temperatures; the symptoms are pitting on the skin, internal browning and failure to ripen. In potatoes, very low temperatures convert starch into sugar. These products have their own safe temperature ranges and are kept at higher temperatures.
Can apples and lettuce be stored in the same room?
They should not be. Apples produce high amounts of ethylene, and lettuce and other leafy greens are highly sensitive to it. Even if both are at the correct temperature, the sensitive produce will yellow within a few days and lose its shelf life. If a separate room is not possible, they should not be accepted in the same period or, at the very least, should be given short-term separation supported by an ethylene scrubber.
What should the relative humidity be in the store?
For most fruit and vegetables, a range of 85-95% is targeted; high-surface-area produce such as leafy greens and broccoli requires the upper end. Produce with a dry skin, such as onions, garlic and squash, is instead stored at lower humidity, around 65-75%. The most effective way to maintain humidity is to operate with a small temperature difference using a large-surface evaporator.

Related articles

Contact

Let's talk about production, processing and storage.

Share your needs; let's assess capacity and our proposed solution together.

Get a Quote
Ozan Global Holding
An Ozan Global Holding companyA multi-sector industrial group producing concrete, pipe, mining, maritime and food products. Holding website ↗